tec-science
I am an engineer by profession and teach mechanical engineering and physics at a vocational school. In my free time I like to create 3D animations, even though I'm not a professional at it. This Youtube channel is the logical result of combining my profession and my hobby. Have fun with it.
On my channel you will find all kinds of stuff about mechanical engineering and physics for study, school and work.
The images and animations shown in the videos are almost exclusively generated with the 3D-software Blender. Therefore, the images and animations do not claim correctness of the illustrated contents.
Feel free to share the videos, but do not upload them to other platforms without first asking for consent.
Disclaimer: www.tec-science.com/disclaimer
Проектирование компонентов, работающих под давлением | Определение размеров | Контактное давление
Проектирование компонентов при растяжении и сжатии | Предел текучести | Определение размеров
Damped Oscillations | Derivation of the Differential Equation | Period | Frequency | Formula
Простое объяснение испытания твердости по Виккерсу
Смещение профиля эвольвентных зубчатых передач | предотвращение подрезов | вывод
Жидкостный маятник | Вывод дифференциального уравнения | Частота | Период | Колебания U-образной ...
Простой маятник | Вывод дифференциального уравнения | Период | Частота | Формула
Вертикальный пружинный маятник | Вывод дифференциального уравнения | Период | Частота | Формула
Горизонтальный пружинный маятник | Вывод дифференциального уравнения | Период | Частота | Формула
The Equation of Motion of Harmonic Oscillation Explained Simply
Введение в колебания
Bearing Arrangements | Mounting | Non-Locating | Adjusted | Floating | Back-to-Back | Face-to-Face
Calculation Rolling Bearings | Bearing Size | Static & Dynamic Load Rating | Life | Operating Hours
Basic Designation System of Rolling Bearings | Dimension, Width & Diameter Series | Bore Code
Rolling Element Bearings Simply Explained | Thrust Bearings | Balls, Rollers, Needles, Cones
Designation System for Steels simply explained | DIN EN 10027 | Chemical Composition | Intended Use
What is a Keyed Joint? | Shaft-Hub Connection | Calculation | Method C | Design
Geometric Dimensioning & Tolerancing (GD&T): Position Tolerances (Parallelism, Position, Runout ...)
Geometric Dimensioning & Tolerancing (GD&T): Straightness, Flatness, Roundness, Cylindricity
Hole Basis and Shaft Basis System Simply Explained | Fit | Limit Plug Gauge | Limit Snap Gauge
Fits simply explained (clearance fit | transition fit | interference/press fit)
Basics of dimensional tolerancing (General Tolerances | ISO Tolerances | Deviations | Fits)
Calculation of Cutting Data in Turning (Spindle Speed, Feed Rate, Depth of Cut, Roughness)
Basics of Turning (Depth of Cut | Feed | Feed Rate | Nose Radius, Nose Angle, Approach Angle)
Basics of Milling | up-milling (conventional) | down-milling (climb) | calculation speed & feed rate
Drilling, Thread Cutting, Countersinking and Reaming
Basics of Machining Part 2 | Drilling, Turning, Milling, Wedge, Clearance, Rake Angle, Feed, Infeed
Basics of Machining Part 1 | Cutting Forces | Wedge | Force Parallelogram
Surface Specifications ISO 21920 | Roughness | Mean Roughness Depth | Arithmetic Mean Roughness
Belt friction equation | derivation of the Euler-Eytelwein formula | problems & solutions