Ayyan Engineering Solutions
Ayyan engineering Solutions are providing training of PLC and HMI online and offline both methods.
Our Mission is just to spread automation knowledge to others.
This channel's purpose is to give basic Plc training free of cost.
.
If you want to purchase and sell PLCs, VFD, HMI, sensors. You can contact us.
Contact info:
Whatsapp: +92-333-8860576
Email: [email protected]
Facebook: https://www.facebook.com/ayyanengineeringsolutions/
Website: www.ayyanengineeringsolutions.com
01-Introduction of Rslogix5000 software | Basic PLC programming | Allen bradley PLC | Rockwell
02-How to add Siemens S7-1200,S7-1500 hardware in TIA Portal Software | Hardware configuration
Introduction of TIA PORTAL Software Siemens | S7-1200 PLC Course | S7-1500 PLC Course | TIA Portal
Связь RS485 между ПЛК | Связь Delta между ПЛК | Двухпроводная связь | Связь с ПЛК
Знакомство с программным обеспечением WinproLadder для ПЛК Fatek | Программирование ПЛК Fatek | В...
How to Show Numerical Values in Ignition SCADA| What is SCADA| Kepware Server| SCADA System
Delta PLC PID Control Programming Training | PID Pressure Control System | Delta PLC
What is Stepper Motor and Stepper Motor Programming and wiring in Fatek PLC in English Language
Что такое шаговый двигатель, программирование и подключение шагового двигателя в ПЛК Fatek на язы...
Siemens PLC Training for Beginners| Ladder Diagram| Siemens PLC Course| S7-300 | Simatic Manager
10-Comparison commands Equal, less than, greater than Programming in S7-300 Siemens Simatic Manager
09-Mathematics Functions Addition +, Subtraction -, Division /, Multiply * Programming in S7-300 PLC
08-Output Analogue module 4-20mA, 0-10V Programming in Siemens S7-300 | Siemens PLC Course | Siemens
07-Input Analogue Sensor 4-20mA, 0-10V /module Programming in Siemens S7-300 | Siemens PLC Course
06-Siemens PLC Counter Programming & How many types of counters in S7-300 Simatic Manager Software
05-Siemens PLC Timers Programming & How many types of Timers in Siemens S7-300 PLC Simatic Manager
04-Basic Siemens PLC Programming S7-300 in Simatic Manager Software | Siemens PLC Course | Bit Logic
03-How to use Simulation PLCSIM in Simatic Manager Software S7-300 PLC | Siemens S7-300 PLC Course
02-Как добавить оборудование ПЛК S7-300 в Simatic Manager и как читать теги модулей | Курс по ПЛК...
01-Введение в ПЛК и программное обеспечение Siemens для начинающих | Курс по ПЛК Siemens | Аппара...
Fatek PLC Programming in 1 hour| Basic PLC Training| Ladder diagram programming|Complete PLC Course
08-How to use Comparisons Commands Equal(=), Less than, Equal Than, in Fatek PLC | Comparison
07-How to use Data ADDITION(+), Subtraction(-), Multiplication(*), Division(/) In Fatek PLC| Math
06-How to Use Timers,Counter 16bits,32bits, Rententive and non Retentive in Fatek PLC Programming
05-How to use Inverse, Set ,Reset, TU Power Flow, TD power Flow commands in Fatek PLC | Fatek PLC
2- Fatek PLC input/output wiring| Plc Sinking & Sourcing wire | Fatek PLC wiring | NPN & PNP Wiring
04-What are Memory bit M, Data Register D,R, & types of it in Fatek PLC in English | Internal Relay
03- Fatek PLC input & Output addressing , Ranges of timers, Counters, Data registers in English
02-How to use Protrusion Command In Solide Edge V20 | Basic Course Solid Edge For Beginner|3D Design
24- Introduction, Configuration, Programming of CC-Link in Q series Mitsubishi PLC in Urdu/Hindi