Husky Liners® Mud Flap, Ram w/flares Installation Video

https://huskyliners.com/p/husky-liner...

Husky Liners® form fit Mud Flaps are made from durable, impact resistant all-weather thermoplastic that’s as tough as nails (or rocks for that matter). They’re easy to install, conform perfectly to your fenders, and protect your ride and those around you from the rage of the road.

Form is our function. - Our form fit Mud Flaps are tailored to match your fenders perfectly. If only our pants could fit like that.

Wider is better. - Our FormFit Mud Flaps are built to the maximum width for full tread coverage of single or dually factory tires. We don’t mess around with mess around.

Tougher than nails (or rocks for that matter). - Our durable, impact resistant all-weather thermoplastic material holds up to whatever the road spits at it.

You’ll be muddin’ in no time. - So quick and easy to install you’ll be on the road to off-roading in no time.

Looking slick. - The sleek style of our FormFit Mud Flaps give your ride a factory look, only better.

Get behind the Shield. - Our Exclusive Husky Shield® Film is easy to install and provides an invisible protective barrier between the Mud Flaps and the vehicle’s paint.

Guaranteed… FOR LIFE. - No hassles, no guff. If you have a problem, we’ll replace it. Capeesh? For details: HuskyLiners.com/ForLife

Born in the USA. Made in the USA. - When we said the Pledge of Allegiance in school, we meant it.

–

Transcript:

Husky Liners® form fit Mud Guards are made from durable, impact resistant all-weather thermoplastic that’s as tough as nails (or rocks for that matter) and as you will see in this video, they are ridiculously easy to install.

First, let’s verify the vehicle application and part number you received matches the intended part you ordered. To do this, find the bar code on the box and check that the information matches your specific truck.

Next, unpackage the Mud Guards, fastener kit and instructions from the box. If you ordered a MudGuard combo pack, please identify which are the front and rear mud guards to ensure for proper installation.

To protect your fenders against wear, you’ll want to install the paint protection film over the mud guard mounting surface.

Clean the area where the mud guard will be installed.

Please note, turning the wheel for front installation will ease installation.

We have provided both a left and right side pre-cut template. Remove the backing liner by folding the liner at the center cut of the template, separating the film sides and peeling the film templates from the backing liner.

To determine where to place the paint protection film, position the mud guard on the fender. You will notice an LH for left hand side and an RH for right hand side.


Remove factory fasteners and set aside for later use.

Next, to remove the protection film from the liner and to flood the adhesive side of the film, mix a wetting solution of 1 pint of water with 4 drops of liquid dishwashing detergent.

Then, using a spray bottle or sponge, wet the film with the wetting solution and remove the protection film.

Thoroughly wet the location of the fender where the film will be installed with the wetting solution.

Position the adhesive side of the film on the fender and flood with the wetting solution.

Double check the location of the film using the mud guard and reposition if necessary.

If it is positioned correctly, using a sponge or clean shop towel, squeegee any air bubbles and wrinkles from the film.

You will want to allow the film to dry before installing the mud guard.

Repeat this process for both the front and rear film installation.



Peel off the red protective cover from the 3M adhesive on the MudGuard.

Next, attach the front mud guard to the fender with the factory fasteners. You will want to double check the fit and ensure the mud guard is parallel to the ground before tightening.

Be sure to press firmly on the area with the 3M adhesive tape to make sure adhesive is set.
Finally, install the spring clip over the mudguard and the fender lip at the location with the raised tic marks.


Attach the mud guard to the fender with the factory fasteners. Double check the fit and ensure the mud guard is parallel to the ground.

From all of us at Husky Liners, thanks for watching and for those who have purchased a new set of Mud Guards, we appreciate your business. We hope you experience many years of increased protection for your truck. Should you have any questions or concerns, please do not hesitate to contact us at (800) 344-8759.

Magnus: Husky Liners. Guaranteed for Life.