VanMoof S3/X3 Battery Replacement: A Step-by-Step Guide

Hello guys thanks for watching..

Also I'm trying to make a channel regarding problems like this
if you have any suggestions or challenges for me I'm happy to try solving them :)
if I need to get in touch please do so on [email protected]

this is the full list of errors to your S3/X3 Bike 🚲

Here are the battery-related
errors for the VanMoof S3:
1. BAT SCP: Short circuit
protection (main battery
related)
2. BAT_ MOTP: Mosfet over
temperature protection (main
battery related)
3. BAT_PDSCP: Pre discharge
short circuit protection (main
battery related)
4.BAT_PDOCP: Pre discharge
overload circuit protection
(main battery related)
5. BAT_UVP2: Under voltage
protection 2 (main battery
related) (try charging for a
longer period, could solve
issue)
6. BAT_UVP1: Under voltage
protection 1 (main battery
related)
7. BAT_ OVP2: Over voltage
protection 2 (main battery
related)
8. BAT_OVP1: Over voltage
protection 1 (main battery

8. BAT_OVP1: Over voltage
protection 1 (main battery
related)
9. BAT_COCP1: Charge over
current protection 1 (main
battery related)
10. BAT COCP2: Charge over
current protection 2 (main
battery related)
11. BAT DOCP2: Discharge
Over current protection 2 (main
battery related)
12. BAT DOCP1: Discharge
Over curent protection 1 (main
battery related)
13. BAT_CUTP: Charge under
temperature protection (main
battery related) (it's too cold to
charge)
14. BAT COTP: Charge over
temperature protection (main
battery related) (it's too warm
to charge)
15. BAT DUTP: Discharge
under temperature protection
(main battery related) (it's too
cold to discharge)
16. BAT DOTP: Discharge over
temperature protection (main
battery related) (it's too hot to
discharge)
17. BATFP: Permnanent fail
(fuse burn) (main battery
related) (likely socket short
circuit)
18. Error 17:
BATTERY_ NO_DSG - Could
not set discharge mode (main
battery related)
19. Error 18:
BATTERY_MISSING - Signal
bat_key_in is low (main battery
related) (battery not
recognized, also the error you
get when no battery is present)
20. Error 19:
BATTERY COMMUNICATION
Modbus battery (main battery
related)
21. Error 20:
BMS
seems to shutdown (main
battery related)
22. Error 21:
NO_ CHARGE_CURRENT
Charging state but no current
reported (main battery related)
23. Error22
SSP TI Motor chip (module
related)
24. Error 23:
BLE chip (module related)
(Bluetooth chip)
25. Error 24: OAD _ABORT
Transfer from app aborted
(Module related) (Upload was
aborted?)
26. Error 25: OAD_ CRC -
Transferred image crc error
(Module related)
27. Error 26:
OAD file transfer took too
long (Module related)
28. Error 27: OAD_PACK - No
or invalid file in pack (Module
related)
29. Error 28: ICF_TIMEOUT -
Timeout during flash
programming (Module related)
HEADER -
30. Error 29: ICF
Header not found (Module
related)
31. Error 30: \CF_ NO_FILES -
No files in pack (Module
related)
32. Error 31: ICF ERASE -
Flash erase error (Module
related)
33. Error 32: ICF WRITE -
Flash write error (Module
related)
34. Error 33: ICF CRC - File in
pack has CRC error (Module
related)
35. Error 34 -
Programming of the motor
Controller failed
36. Error 35:
PGM_BATTERYWARE -
Programming of the BMS
Controller failed
37. Error 36:
PGM_SHIFTERWARE -
Programming of the shifter
Controller failed
38. Error 37: PGM_BLEWARE -
Programming of the BLE
Controller failed
39. Error 38: -
STVC3115 read error, LiPo
might be missing (Module
related) (check if battery
m o io hor)
40. Error 39:
READ_LIGHT
_SENSOR
CM3232 12C read u - Kick-
Lock coil not detected
44. Error 43:
SHIFTER_NOT_IN_GEAR -
After 10 tries, gear has not
been reached
45. Error 44:
SHIFTER
COMMUNICATION -
Modbus Shifter (Shifter not
recognized) (Plug in tester
Shifter)
46. Error 45:
MOTOR MOTOR CABLE -
Bit2/NTC motor cable not
Connected (Motor not
recognized)
47. Error 46:
MOTOR MOTOR_OVER CURRENT
DRV8301 over temperature
(bit6)
48. Error 48:
MOTOR CONTROLLER_ERROR
Error in user parameters
(bit8) (replace motor)
49. Error 49:
MOTOR CURRENT_ERR -
Current offset calculation +-
from default value 1.0
50. Error 50:
MOTOR_VOLTAGE_ERR -
Voltage offset calculation
+*from Vbat/2 or Vbat
51. Error 51:
MOTOR_ DERATING - Max
current limited due to high
temp
52. Error 52:
MOTOR TORQUE_SENSOR FAIL
Torque sensor failed, only if
sensor required
53. Error 53:
MOTOR NOT READY - Motor
not ready during motor test or
error
54. Error 54: NO SIMCARD -
SIM card not present (Module
related) (SIM not recognized)
55. Error 55: 12C3_FAIL -
Started with l2C error on bus 3
56. Error 56: CCID_SIMCARD -
SIM card wrong CCID
(VanMoof) number
57. Error 57: READ_SIMCARD -
SIM card is detected but no
communication (Module
related) (Check ICCD number
in BO)
58. Error 58: GSM_MODEM -
Modem startup sequence
failed (Module related) (often
gone after reset)
60. Error 60: FACTORY_MODE
Display 60 when factory

hope it helps ☺️