Idle Relearn - FX35, I35, M35, G35, G37, 350z, 370z, Maxima, Murano, Sentra, Altima, M45, M56,

How to Reprogram your Throttle Body. The easiest youtube idle relearn video. I show you how to reset your idle to OEM spec at 650 RPM. ENGINE CODES p0507 p2102 p0603 p2118 P0123 and P0233

MAKE MODEL YEAR CYL LITER
INFINITI G35 2003 - 2006 V6 3.5L
INFINITI I35 2002 - 2004 V6 3.5L
INFINITI M35 2006 - 2008 V6 3.5L
INFINITI TRUCKS FX35 2003 - 2009 V6 3.5L
NISSAN 350Z 2003 - 2005 V6 3.5L
NISSAN ALTIMA 2002 - 2006 V6 3.5L
NISSAN ALTIMA 2002 - 2006 L4 2.5L
NISSAN MAXIMA 2002 - 2008 V6 3.5L
NISSAN SENTRA 2002 - 2005 L4 2.5L
NISSAN SENTRA 2003 - 2005 L4 1.8L
NISSAN TRUCKS MURANO 2003 - 2009 V6 3.5L
NISSAN TRUCKS QUEST 2004 - 2009 V6 3.5L
NISSAN 370Z
INFINITI G37

Preparation

Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment.

Battery voltage: More than 12.9V (At idle)
Engine coolant temperature: 70 - 100 C (158 - 212 F)
Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral)
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed-up (Drive vehicle for 10 minutes.)

Operations Procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 second.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone.
If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.

Accelerator Pedal Release Position Learning
Operation Procedure

1. Make sure that the accelerator pedal is fully released.
2. Turn ignition switch “ON” and wait at least 2 seconds.
3. Turn ignition switch “OFF” wait at least 10 seconds.
4. Turn ignition switch “ON” and wait at least 2 seconds.
5. Turn ignition switch “OFF” wait at least 10 seconds.

Throttle Valve Closed Position Learning
Operation Procedures

1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch to “ON”.
3. Turn ignition switch to “OFF” wait at least 10 seconds.
Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.

Idle Air Volume Learning (Throttle Position Learning)

It is better to count the time accurately with a clock.

1. Perform “Accelerator Pedal Released Position Learning”.
2. Perform “Throttle Valve Closed Position Learning”.
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Confirm that the accelerator pedal is fully released, then turn ignition switch “ON” and wait 3 seconds.
6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.
7a. Fully depress the accelerator pedal (HARD)
7b. Fully release the accelerator pedal.
8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.
9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.
10. Start engine and let it idle.
11. Wait 20 seconds.
12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications.

p2102 p0603 p2118 P0123 and P0233

Nissan Electronic Throttle Body (ETB) Re-Learn Procedure