P0740 Honda Acura Linear Solenoid Replacement Fix | Accord Odyssey Pilot Ridgeline

P0740 is one of the most common transmission trouble codes. It means that the Accord‘s computer has detected that there is an issue with the torque converter clutch (TCC) solenoid circuit.



The TCC “locks” the drivetrain, which allows for a true mechanical connection between the transmission and the engine. In effect, this allows an automatic transmission to function like a manual transmission at certain speeds and engine loads, and eliminates all slipping from the transmission.


P0740 Symptoms: Honda Accord
The symptoms of P0740 vary greatly. If the converter stays unlocked, it can be a nuisance. If it locks when it shouldn’t be, that’s where it can get dicey.



The most common symptoms include:

Poor Gas Mileage- If the converter is not locking at speed, the engine’s RPM’s will stay higher. This decreases fuel mileage.
Stutters and Stalls- This would be a symptom of the transmission locking when it should not be. It feels exactly like when you need to downshift in a manual transmission.
Higher RPM on highway- If the converter is not locking, it can lead to higher RPM on the highway. This increases fuel mileage and makes the transmission operate at a higher temperature.
Service Engine Soon Light


Transmission Fluid
If there isn’t enough transmission fluid, the transmission will not be able to operate normally. There are many symptoms of low transmission fluid. The most noticeable one is going to be the transmission slipping.

If the transmission fluid is dirty or burnt, it can make the transmission behave in a way that is not normal and throw the P0740 code. Here’s a pretty good guide on transmission fluid color.

If the fluid is low or bad, replacing should be considered an urgent priority. The good news is that transmission fluid and filters are cheap.

Wiring Issues
The wiring harness that goes to and from the transmission is one of the more vulnerable pieces of wiring on a vehicle. Inspecting the harness for obvious signs of distress, checking the connection at the transmission itself, and finally a continuity test can go a long way in diagnosing your Accord.


TCC Solenoid
It is highly likely that the torque converter clutch solenoid (TCC) has gone bad. But, jumping straight to this conclusion without inspecting the transmission fluid and wiring can cause a lot of undue headache.

Torque Converter
The torque converter itself or torque converter clutch can go bad and throw the P0740 code.

Problem in the Case
If the TCC seems to be functioning properly, it may be that the problem is in the transmission case itself. It could be a valve body issue, a problem with the pressure going through the transmission, or a clogged filter.





P0740 Article:
WILL UPLOAD SOON





More About BundysGarage:
https://goo.gl/qv3Wzc

Questions, Comments, Concerns:
[email protected]

Twitter:
  / bundysgarage  
@bundysgarage

On The Web:
http://www.bundysgarage.com

Music by Randall Kent: As seen on NCIS
   • Randall Kent - Going Home (Featured on NCI...  

All Rights Reserved 2020
© Copyright 2020
Bundys Garage

All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: [email protected]

DISCLAIMER - DISCLAIMER - DISCLAIMER

Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.