How to Make a Dutch Hood for Falconry

How to Make a Dutch Hood

Featuring Cody H.'s two methods...
Covers both glued and stitched.

To learn more about how to tie the "three turks" head knot, follow this
link! http://www.falconryforum.co.uk/showth...

To learn more about how to install the braces on the hood, check out
our video here!
   • Installing Braces on a Hood  

MESSAGE FROM THE MAKER OF THIS HOOD

To all viewers of this vid,

Given the video was silent it was hard to convey to much info so
hopefully this will clear up any questions.

On Leather:
Leather should always be vegetable tanned. This leather will form
better to the block and last longer than chrome tanned and brain tanned
is far to floppy. Kangaroo or Kip (about a year old cow) is very good
and kangaroo is probably best as it is very rip resistant. For a RT
hood 3oz is probably as thin as it should get. Especially as a
beginner, 4 to maybe even 5 oz would be best as it leaves room for
error when punching holes. If you buy your leather natural color and
plan to dye it make sure there is no oily topcoat and use a real
leather dye form Fiebings of Tandy.
Always test your leather before buying it. Cut a slit in it and pull.
You should not be able to rip it easily.

On Cutting:

Keep your knife sharp and at 90 degrees to the leather. Remember only
cut half way through on the beak opening!!!

On Marking and Punching holes:

Mark about 3/16 in from the edge with dividers or a groover. Roll a
marker along it. Don't push to hard or you can go through thinner
leather. You should have AT LEAST 8 stitches/inch.
When punching holes leather should be lightly damp. Your awl should
come out about halfway through the leather erring on the deeper side.

On Sewing and Thread:

Thread should be cotton coated polyester or linen (linen is best and is
available from www.wmboothdraper.com get the 60/2 and use 3 strands or
so) Wax it well with beeswax and lightly twist the strand together.
Needles should be small tapestry needles. These are blunt so as to not
puncture the thread.

Sewing should be done with the leather lightly, lightly, lightly,
lightly, lightly, lightly, damp. Too damp and when it dry's your seam
will be gaping open & letting light in.

On Blocking:

This is pretty obvious from the video.

On the top Knot:

This is NOT obvious from the video. I should have done light colors to
make it visible. Sorry. One of these days I'll make a vid on that
specifically.

On Braces:

See Israels other video.

On the Pink and Black Zebra Blow Dryer:

Its not mine:)


On Finishing:

There are a couple options here.

You can give it a coat of Super Sheen from Tandy leather.

You can lightly oil it with Pure neatsfoot oil ( this may darken colors)

You can spit shine it with shoe polish.

And last but not least you can clean it with saddle soap.

On Storing you hood:

Store hoods with the braces open and stuffed with paper. Keep the top
not protected and every once in a while oil your braces.

Note: You should NEVER get oil on your bird feathers so the oil on the
braces should be liquid (not a grease) and should be allowed to soak in
over night in a warm place.



I hope this clears up and questions you all might have had.


Sincerely,
Cody ( the guy that made the hood )

www.falconrytold.com

Support Future Uploads!
www.patreon.com/falconrytold

Official Merch!
https://www.spreadshirt.com/user/Falc...

Like us on Facebook! www.facebook.com/falconrytold

Follow us on Instagram!
@falconrytold