Full Review ELASTIMOlD Termination 500MM SQ Cable With 13.8KVA

• Hello Guys I hope like this video.

• Don't forget to LIKE,COMMENT,SHARE and SUBSCRIBE and Don't Forget Press to hit the Bell🔔icon

°°°°°°°°°°°°°°°°°FIRST FOLLOW SAFETY°°°°°°°°°°°°°°°°°°°°°°


This video Elestimold Termination For You Tips
Termination Basic Working Measurements
Filing 19.5cm
Heat Shrink Tube filling Down With semiconductor 2.5cm
XLPE Cutting Fixed Lugs measurements

Termination Full Details
Instructions for installation of elbows for three-way cables

ELBOW ETC2-3C

INSTALLATION INSTRUCTION FOR THREE CORES ELBOW CONNECTOR

The ETC2 connector are designed to provide fully shielded dead front cable connection to medium voltage bushing C. Suitable for Installation up to 630 ampere, Elbow is rated for use up to 15KV.

IMPORTANT

At apparatus must toe-energed dung lao

Excedatortion of the assembled product may result in its failure

Thie bow stelt be rosaliant only by qualified persons who had good training nintatanon and handing high voltage sechical agipment. These inauctione anded astute for adequate traming or experience in such sahity practices and we not snough for every possible contingency aroblem.

Check content of package to ensure they are complete and undamaged and to mure prope it with the cable Have a gution and

netbushing mated sombrain shouldn't be allowed to carry fuf weight Therefore nessary to clamp the cable inmediately beyond cable breakout

Read staliation instructions before starting and Inikow the sahery practices

Filmore information on instaltation or sartsal The nearest ELSEWEDY ELECTRIC office

1. Store the transparent tube over the cable Jacket

2- Position the cable so it is located in the final assembled position with enough slack to provide adequate clearance for removing the elbows as shown in fig (1).

3- Prepare the cable as shown in fig (2). All dimension in mm

ETC2 to ensure complete access to cables of any size, even if completely insulated and suitable for installation up to 130 amps. تعمل الألبو ETC2.
general

Power must be disconnected from the appliance during installation
It may cause the product to break down after installation‎
And use high-current equipment in peace, and these instructions are not a substitute for training and guidance

The value in the field of safety is not enough for everyone.

The administrator of the contents to make sure that it is complete and does not have any damage and to make sure that it is suitable

Complete with cables and be ready for all the necessary duration.

The device may not be able to handle the cable, and it is better to connect the player near me

End of legislation Read all installation instructions before starting installation and follow the instructions for safety and security for all

For more information on installation or parts, call the office near the office

Al Suwaidi Electric‬‎

Adjust the cable taking into account the distance required

for installation as in figure (1)

The cable is prepared as follows (1) All sizes
‬‎Cable prepation

1. Wrap a colored PVC tape at 25mm from semi-conductor edge to be used as a mark to fold copper wire.

2. Fold back Cu wires on top of PVC tape

3. Position the copper braid on cable copper metallic screen using either spring or coppe wires which should be carefully welded.

4. In case of connecting cable armor along with metallic screen, secure copper braid with armor using clamp, then wrap a layer of mastic tape over clamp

Accoirding to the COPPA Policy
Disclaimer- don't take this video for copyright song and video. All of human made in pc and phone thand you. This video is related to the main line connection of electricity. This Video Learning of all Electric and electrician 11/13 KV Line Joint And Transition Transform To 4Way Cable In put To out Going. Thank You. EF Channel Of Cable jointer

#SUBSCRIBE_WOCY_NOW.
#THANS_FOR_WATCHING


copyright disclaimer under section 107 of the copyright act 1976, allowance is made for fair use for purposes such as criticism, comment, news reporting, teaching and research.

Thank You.

Youtube.CABLE_JOINTER