I built a 200 MPH drone. You can too. || AOS-HS5 How-To

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: https://www.fpvknowitall.com/ultimate...

SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia

THIS IS MY FULL TIME JOB. Here are other ways that you can support me: https://www.fpvknowitall.com/support-me/

---

I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.

Buy the AOS-HS5 full kit at:
CNCDrones - https://bit.ly/3YBST4c

Buy the AOS-HS5 3D printed parts at:
Brain3D - https://bit.ly/3UMuFmx

Buy a completely built AOS-HS5 at:
QuadStandardLabs - https://bit.ly/3ArNCEp

Buy T-Motor VELOX 2808 1950kv motor at:
GetFPV - https://bit.ly/40IJSZY
Amazon - https://amzn.to/3O2aKw7

Buy the Rotor Riot Brave F7 FC at:
Rotor Riot Store - https://bit.ly/3WZaVMR

Buy the Foxeer Reaper 65A 8S ESC at:
RaceDayQuads - https://bit.ly/40HoUKX

If you can't get that exact ESC, choose another 8S ESC from this list:
RaceDayQuads - https://bit.ly/3UPwcsi

Buy the HQ 5.3x8 thin electric prop at:
HQ Store - https://bit.ly/3CkQnYB

Buy the GNB 1100 mAh 8S battery at:
RaceDayQuads - https://bit.ly/3OUB9Ol

Buy the ISDT Air8 Charger at:
GetFPV - https://bit.ly/3Ci7zhi
RaceDayQuads - https://bit.ly/3MdepEh

Buy the HOTA T8 Charger at:
GetFPV - https://bit.ly/4ewdgWd
RaceDayQuads - https://bit.ly/4hG7Paf

MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.

---
00:00 - You can fly over 200 mph!
02:29 - What comes in the kit
03:46 - The STL are not publicly avilable
04:51 - Motors: 2808 1950 kv
06:08 - Prop: HQ 5.3x8 "thin electric"
07:25 - Battery: GNB 1100 mAh 8S
08:46 - ESC: Foxeer Reaper 65A F4
09:36 - FC: Rotor Riot Brave FC
10:52 - vTX: DJI O3
11:55 - Mount the ESC
14:54 - Mount the motors
20:22 - All four motors and ESC are installed
20:55 - Install bottom fairings
22:26 - Re-pin FC to ESC wire harness
27:29 - The final ESC to FC harness
28:35 - Build the GPS wire harness

SH wire harness set - https://bit.ly/2IkPQ7s

32:05 - Prep the receiver wire harness
32:43 - Mount the O3 and RX to the top plate
34:51 - Smoke check!
36:40 - Have I earned your support yet?
37:39 - Betaflight Setup

Easiest Way To Flash and Bind ExpressLRS!
   • Easiest Way To Flash and Bind ExpressLRS!  

The secret to faster ELRS connection -    • Faster ExpressLRS connection with INIT_RATE  

Pastebin link for my O3 OSD setup - https://pastebin.com/wSquhCxt

42:51 - How to set up pusher motors and props
45:32 - Mount the FC in the frame
46:24 - Mount the GPS in the shell
47:39 - Mount the O3 camera
48:59 - Mount the top plate in the canopy
50:31 - The finished nose-cone
51:14 - Install the top shell on the frame
52:49 - Mount the bottom shell
55:03 - Special note about the props
58:04 - The fatal test flight
59:13 - Conclusion

A more traditional build that "allegedly" goes 160 mph! -    • He gave me a "160 mph" Racing Drone. I'M N...