This 3D Printed Contraption Cools My Office!?!

Mandic Labs 2.0 is supported by:
🔥 Prusa3D – http://www.prusa3d.com/#a_aid=MandicR...
🛠️ PCBWay – https://pcbway.com/g/k66yI7
------------------------------------------------------------------------------------------------------------
My office was basically a convection oven.
And me? I don't do well in the heat. So I built a semi-passive airflow system that uses thermal dynamics (yes, I know) to pull cool air from the warehouse through a filtered inlet and silently exhaust the hot air out. It’s not your average HVAC solution — but it’s quiet, efficient, and full of 3D printed madness.

In this video, I design, print, and install a full silencer system for an inline fan, use a cardboard concrete form tube (you heard me), and make the most cyberpunk cooling system this side of the galaxy. This is the new way I keep Mandic Labs 2.0 from melting me during filming.

🛠️ Designed in Fusion 360, printed on the Prusa Core One print farm.
------------------------------------------------------------------------------------------------------------

Check out more MandicReally and ways to support the channel:
🌐 https://www.mandicreally.com/links

🙏 Special thanks to @multiboard_io for supporting the studio as well! : https://than.gs/u/234635?affiliateCod...
------------------------------------------------------------------------------------------------------------

🛒 Featured Products & Recommendations (Affiliate Links):
*** AC Infinity 8" Inline Fan: https://amzn.to/4ozCEkv
*** 8" Vibration Isolators: https://amzn.to/3UFgqiX
*** 8" Flex Ducting: https://amzn.to/4feRico
*** 12" Concrete Form Tubes: https://shoplowes.me/4mhZMlm
*** Mineral Wool Insulation: https://amzn.to/40JZ9ca

------------------------------------------------------------------------------------------------------------

🎥 My Filming Gear (Affiliate Links):
Main Camera – https://bhpho.to/3RStTnz
Main Lens – https://bhpho.to/4avDFmt
Video Recorder – https://bhpho.to/3Oa4qmZ
Action Cam – https://bhpho.to/45CS10Q
Wide Lens – https://bhpho.to/3RXQXBj
Motorized Slider – https://bhpho.to/48YMmnD
Studio Mic – https://bhpho.to/4216F1z
Voiceover Mic – https://bhpho.to/46uECsE
Monopod – https://bhpho.to/3PT2yir
Tripod – https://bhpho.to/3PSKXY4
Primary Lighting – https://bhpho.to/3RXSmb3
Accent Lighting – https://bhpho.to/3RXVfsf
RGB Lights – https://bhpho.to/3S77IbO
Drone – https://bhpho.to/423XrS6

------------------------------------------------------------------------------------------------------------

🧪 These are my real-world opinions based on hands-on use.
Some links are affiliate links, which means I may earn a small commission—at no extra cost to you.
Not a paid endorsement unless explicitly stated in the video.

------------------------------------------------------------------------------------------------------------
⏱️ TIMESTAMPS:
00:00 - Intro
00:41 - AC For Thee
1:28 - Design Discussion
2:28 - Silencer Start
3:10 - The Fan
3:58 - Vevor PSA
4:46 - Silencer Assembly
10:26 - Print Design Details & Assembly
13:22 - Install Begins
14:20 - Office Inlet Vent
14:46 - Ceiling Vent
15:46 - I Screwed Up...
16:25 - Assembly Mockup
17:10 - Hanging The Contraption
17:55 - Connecting the Ducting
19:14 - Testing The Contraption
20:49 - Test Results
22:32 - Sound Level
23:32 - Worth it?
24:22 - Outro

#mandicreally #prusa3d #pcbway