🔥🛠 How To Clear Harley Code & Quickly Diagnose the Problem

Do you know how to clear Harley code and do quick diagnostics. Knowing how to clear Harley code will help you identify issues with your motorcycle. This might be really helpful in your troubleshooting process.

List of codes was too long to add them all here but you can check it @ https://www.wilkinsharley.com/--Check...

1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
2- Push odometer reset button in & hold.
3- Turn ignition switch to Ignition and release the odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “DIAG” should then appear.
4 – Push the odometer reset button once and you will seethe selection menu “PSSPt” with the first P flashing.
5 – Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM(Electronic Control Module)[EFI] /Ignition Control Module[Carbureted])
S = TSM/TSSM (Turn Signal/ Security Module)
SP = speedometer
T = tachometer
6 – To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist.
7 – Record the codes.
8 – If DTC’s are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear.
9 – Press and release the odometer reset button to continue to the next module.
10 – Turn Ignition switch to OFF.

On models not equipped with a tachometer “No Rsp” will appear when the tachometer identifier is selected.

“No Rsp” (no response) will also appear if the run/off switch is in the off position when doing this procedure.

Channel about everything motorcycle related from travel to tips, road planning, motorcycle camping, repairs and reviews. I always try to engage with my audience so I treat it as interactive platform for communicating with motorcycle community and provide recommended videos from subscriber. Please join and I promise you won’t be disappointed.

#RidersUnited
CLICK THIS Link to SUBSCRIBE: https://www.youtube.com/RIdersUnited?...
If you would like to see particular types of content then let me know in the comments

My equipment I use:
GoPro9, GoPro5 Session, iPhone 12 mini
Rode Wireless Microphone
Neewer Ring light.
Hohem Gimble.

Help support the channel:
Patreon:   / ridersunited  
Instagram:   / ridersunitedmotorcyclegroup  
Facebook Group:   / 602971673753797  
TikTok: https://vm.tiktok.com/ZMejXBKPY/

DISCLAIMER: This video and description may contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission. This helps support the channel and allows me to continue to make videos like this. Thank you for the support!

Chapters
00:00 Introduction to how to check engine codes on Harley
00:16 Procedure on how to check engine codes on Harley
00:46 Getting to diagnostic codes on Harley
01:19 Overall procedure on running procedure
01:54 Harley codes list location
02:29 Additional information on Harley codes