Upgrading my Langmuir Pro/Do These Upgrades When Setting Yours Up!

Save $100! Langmuir partnered with me to offer my viewers a discount on their purchase of any table offered by Langmuir. Crossfire, Crossfire XL, and the Crossfire Pro. Type ManCrafting in the Discount Code to save $100!
Here's my Affiliate Link http://store.langmuirsystems.com?aff=2

I had a few things I wanted to take care of while doing regular maintenance to my Langmuir Pro this week. The first was to clean everything and empty the old water/Borax solution. It worked. Initially, but as the water table lost water to evaporation, the Borax started crystalizing on the table blades. It then allowed the blades and anything on the bottom of the table to begin rusting. If that wasn't bad enough the splash from the cutting would leave borax based water spots all over the gantry and plasma torch ultimately fouling up the consumables. It was workable but obviously not ideal. I was looking for another option and although I was aware of Plasma table concentrates, I always thought they would be too expensive to use. As it turns out, the cost per table change is only about $15. So much cheaper than I expected. Based on my latest experience of cleaning up the table it's money well spent.
In addition to the new fluid, I wanted to make the process of draining the table a little easier. In order to do that I needed to put dimples in the bottom of the water table where the drain is, think about your kitchen sink. The lowest point is where the drain is. This is what I wanted to do. I picked up a hydraulic hole punch set as well as some dimple dies. I'll add links to what I have as well as at least one other option below. Thanks for watching along as I make some simple upgrades to my Langmuir Pro.

This is not an affiliate link. Just a product that makes using my table more enjoyable. Also, This is only for Steel. Link Below for mixed Metals. https://www.konzenchemical.com/Plasma...
This product is safe for use with mixed metals and prevents the formation of hydrogen gas when cutting aluminum. https://www.konzenchemical.com/produc...

Affiliate Links:
Langmuir Crossfire and Crossfire Pro http://store.langmuirsystems.com?aff=2
SAVE $100 Using Discount Code: ManCrafting
HTP Affiliate Links:
Multi Process Pulse MIG Welder https://800usaweld.com/products/pro_p...
TIG Welder https://800usaweld.com/collections/ht...
Plasma Cutter Used in my videos https://800usaweld.com/products/micro...
Table Torch https://800usaweld.com/products/micro...
Welding Helmet https://800usaweld.com/collections/op...
MIG Gloves https://800usaweld.com/collections/cl...
TIG Gloves https://800usaweld.com/collections/cl...
Best Setup I’ve owned for sharpening my Tungsten Electrodes. I’ve made some, I have bought add-on accessories for my Dremel. This is the best. https://800usaweld.com/collections/tu...

Air Compressor with adequate capacity https://amzn.to/2PFPo7X

Amazon Affiliate Links:
Shelf Brackets I replicated https://amzn.to/2z1MhEp
Certiflat Weld Table http://weldtables.com/#_a_cust8g
Heavy Duty Magnet Square http://amzn.to/2dycStl
Magnet Level http://amzn.to/2cS2ZYV
Round Metal Marker http://amzn.to/2dMikvI
Marker holder and 12 refills http://amzn.to/2dCLTks
Heavy Duty Gloves http://amzn.to/2dMiqDD
Standard Reverse Measuring Tape http://amzn.to/2ut3PRK
Flatback Series Tape Measure 16 Foot http://amzn.to/2fgdIQQ
Evolution Power Tools EVOSAW380 15-Inch Steel Cutting Chop Saw http://amzn.to/2dMhkb4

Photo, Video & Film Production Studio Essentials http://amzn.to/2dMiP9f
USB Microphone - Silver http://amzn.to/2dewgA5
Sony Digital Still Camera http://amzn.to/2dJcAA0



#langmuir #langmuirpro #plasmacnc