1970 Plymouth HEMI Cuda vs 1969 Chevrolet Chevelle Super Sport | STOCK DRAG RACE

T-SHIRTS, HOODIES, MUGS, AND OTHER PRODUCTS FOUND HERE: https://cars-and-zebras.creator-sprin...
1970 Plymouth Hemi Cuda vs 1969 Chevrolet Chevelle Super Sport. Pure Stock Muscle Car Drag Race. Factory Stock Drag Race.
First car is a 1970 Plymouth Hemi Cuda, the other a 1969 Chevrolet Chevelle. The Chevelle is a Super Sport (SS396) with a L89 V8 with factory aluminum heads rated 375 horsepower. The Hemi Cuda has a 426 Hemi V8 rated 425 horsepower. Both cars have automatic transmissions. The Hemi Cuda has 4.10 rear gears, and the Chevelle has 4.88 rear gears. The Hemi Cuda weighs 3745 pounds, including the driver. The Chevelle is 3690 pounds. There were only 652 hardtop Cuda produced in 1970 with the Hemi, and only 67 L89 Chevelles in 1969 with the automatic transmission.

Remember, both cars participate in the Pure Stock Muscle Car Drag Race series, so please check out their website: https://www.psmcdr.com
Also make sure you find them out on Facebook.

The rules for PSMCDR are listed below:

For 1955 to 1979 musclecars built in United States and Canadian assembly plants with a minimum warranty of 12 months and 12,000 miles.
Any car running faster than 11.50 will be disqualified and will not have a qualifying time recorded.
Any convertible running faster than 13.50 will be disqualified and will not have a qualifying time recorded.
Casting numbers must be correct for the year and horsepower claimed including intake manifold, heads, and exhaust manifolds. Blocks do not have to be "numbers matching," but they must be the correct displacement. Overbores up to .070" are allowed. Stock cranks only.
All Engines – compression ratio 1.5 extra points allowed over advertised.
The camshaft must be correct for the year, model, and horsepower claimed for the type of lifter (hydraulic or solid). Roller cams NOT allowed.
The valve train must be factory stock for the year, make, and horsepower claimed.
The ignition system must be stock, including the distributor, cap, coil, and wires. Points may be replaced with any electronic conversion that fits under the stock distributor cap.
The carburetor must be correct for the year, make, and horsepower claimed. Jetting and metering changes are permitted. THE CHOKE ASSEMBLY MUST BE IN PLACE AND FUNCTIONAL!
Cast-iron exhaust manifolds are mandatory and must be correct for the year, model, and horsepower claimed. Internal modifications to the exhaust manifolds are NOT allowed. Under no circumstances will headers be allowed, including those cars that came with headers delivered in the trunk. Pipes must be routed as they were originally for the year, make, model, and engine combination. Mufflers must be stock looking in design, that is, oval in shape. No glasspacks or straight pipes allowed unless installed as original equipment. Maximum muffler inlet and outlet size is 2.5 inches. X & H pipes allowed.
The radiator must be correct for the year, make, model, and horsepower claimed. No lightweight, aluminum radiators allowed.
The camshaft must be correct for the year, model, and horsepower claimed for the type of lifter (hydraulic or solid). Roller cams NOT allowed. Duration at .050" lobe lift must be within 1% of factory specs. Lift at the valve must be within 2% of factory specs. Maximum stall limited to 2200 rpm.
The transmission must be correct for year, make, model and engine of the car. 3-speed manuals may be upgraded to the correct 4-speed if originally available.
The rear axle must be of the same manufacturer as the car. Any gear ratio is allowed.
Reproduction tires or radial tires only.You are allowed to run tires one size over stock.
Factory wheels only.


Disclaimer: The Cars And Zebras YouTube channel is a news channel bringing results/news of drag racing with added history of automobiles. All footage/pictures used were either captured by the Cars And Zebras channel, or used for critique purposes under Fair Use.